Add a switch to your Model 130 DP Gauge

switch130haswitch130laswitch130ja

The 130 models are available with either one or two hermetically sealed reed switches for either high alarm, low alarm, or both. The switches are Single Pole Double Throw (SPDT) with adjustable set points. Switches can be connected to open or close on rising or falling pressure. Switches are enclosed in weather resistant housing. Switch setting is readily made with a screw adjustment. Factory preset switch at no extra charge (Specify Setting) Specify increasing or decreasing range to be set. EXAMPLE: Set at 10 PSID increasing.

About Switch Products

Factory preset switch at no extra charge (Specify Setting)

Specify increasing or decreasing range to be set.

All switches are field adjustable!

 

130switch130ha

Model 130 shown with “HA” switch option
(1) Reed switch in standard condulet enclosure with 1/2" FNPT interface. On orders that do not require wall or pipe mounting the flying leads exit the rear of the gauge.

switch130la

Model 130 shown with “LA” switch option
(2) Reed switches located inside NEMA 4X (Weather proof enclosure) with 7 position terminal strip. An opening at bottom of enclosure accepts 1/2" flexible weather-proof or conduit connector (supplied by customer).

switch130ja

Model 130 shown with “JA” switch option
One (1) Reed Switch w/condulet enclosure &
plug-In (DIN-43650-PG-11) connector. The right angle mating connector is supplied with the gauge. Clocking (orientation) can be changed by prying out the insert and rotating the insert to the desired clocking (90° increments).

Bulletins/IOMs

Model 130 Switch Specifications

The 130 model is available with either one or two hermetically sealed reed switches for either high alarm, low alarm, or both. The switches are Single Pole Double Throw (SPDT) with adjustable set points. Switches can be connected to open or close on rising or falling pressure. Switches are enclosed in weather resistant housing. Switch setting is readily made with a screw adjustment. Factory preset switch at no extra charge (Specify Setting) Specify increasing or decreasing range to be set. EXAMPLE: Set at 10 PSID increasing.

The 130 switch option H & I standard switch enclosure is a condulet with 1/2" FNPT interface. On orders that do not require wall or pipe mounting the flying leads exit the rear of the gauge. For the remaining orders the wires exit the side of the gauge. L & M switch option comes in a NEMA 4X (Weather proof enclosure) with 7 position terminal strip an opening at the bottom of enclosure accepts 1/2" flexible weather-proof or conduit connector (supplied by customer). The terminal strip connection uses 6-32 screws and is rated for use with wire up to 14 Awg.

OPTION

MODEL 130 ELECTRICAL SWITCH CONFIGURATIONS (CE marked)
Switch options not available for Model 130-P "Engineered Plastic Body"

H One (1) Reed Switch with condulet enclosure
(adjustable 10-90% of full scale range)
I Two (2) Reed Switches with condulet enclosure
(adjustable 10-90% of full scale range)
J One (1) Reed Switch with condulet enclosure and plug-in connector
(DIN-43650-PG-11) (adjustable 10-90% of full scale range)
K Two (2) Reed Switches with condulet enclosure and plug-in connector
(DIN-43650-PG-11) (adjustable 10-90% of full scale range)
L One (1) Switch in NEMA 4X plastic enclosure
(adjustable 10-90% of full scale range)
M Two (2) Switches in NEMA 4X plastic enclosure
(adjustable 10-90% of full scale range)

(1) and (2) switch explosion proof class I, div I, groups C & D: Class II,
div II, groups E, F & G for hazardous locations available
Please contact Mid-West at 1-800-648-5778

 

OPTION

ELECTRICAL SPECIFICATIONS (For Resistive Loads)

A SPDT 3W, 0.25 Amp, 125 VAC/VDC (standard)

 

order